| Model | LT-9501H | ||
| Measuring unit compatibility | Measuring units are interchangeable without factory recalibration. | ||
| Display | Minimumdisplayable unit | 0.1 µm*1, 1 µm2, 0.01 ° | |
| Display range | ±9,999.99 µm, ±999,999 µm2, 9,999.99 ° | ||
| Microscope function | Available | ||
| Display cycle | 10 times/sec.*2 | ||
| Terminal block | Analogue output | ±10 V x 2 outputs, output impedance: 100 ? | |
| Timing input | Non-voltage input | ||
| Reset input | |||
| Auto-zero input | |||
| Monitor dedicated power supply | 24 VDC*3 | ||
| Control I/O | Judgment mode | 3-step limits output | For OUT1 and OUT2, and NPN open collector output*4 |
| Binary mode | Binary output | Measured data output (21 bits), OUT1/OUT2/PROFILE selectable NPN open collector output*4 | |
| Strobe output | NPN open collector output*4 | ||
| Binary selector output | |||
| Binary selection input | Non-voltage input*4 | ||
| Stability output | NPN open collector output | ||
| Laser remote input | Non-voltage input | ||
| Program switching input | Non-voltage input x 3 inputs | ||
| RS-232C interface | Measured data output and control I/O (Selectable up to baud rate 115200 bps.) | ||
| Video output | NTSC compliant (PIN connector) | ||
| Main functions | Displacement mode | Distance measurement, Transparent objectthickness measurement, Angle measurement,Relative angle measurement, Surface selection,Dark-out, Mask, Trend graph display, and Scanwidth/interval change*5 | |
| Profile mode | Area selection (Average, Maximum, Minimum, Maximum-to-minimum, Area) Area calculation, Scan width/interval change, Dark-out, Smoothing, Averaging, and Profile data output*6 | ||
| Common | Light intensity accumulation, Microscope (LT-9501H, LT-9501HSO (5654) only), Tolerance judgement, 8-program registration, Calibration, Averaging, Hold modes, Auto-zero, and interface language selection | ||
| Rating | Power voltage | 100 to 240 VAC ±10 %, 50/60 Hz | |
| Power consumption | 110VA or less | ||
| Environmental resistance | Pollution degree | 2 | |
| Overvoltage category | II | ||
| Ambient temperature | 0 to +35 °C | ||
| Relative humidity | 35 to 85 % RH (No condensation) | ||
| Weight | Approx. 2.4 kg | ||
| *1 Display changes every ±0.3 µm. *2 Varies depending on the setting *3 Dedicated power supply for the monitor specified by KEYENCE. *4 Select either the Limits mode or the Binary mode. *5 Select either the Distance mode or the Profile mode. (Only distance mode is available with the LT-9501HSO (5654) and LT-9001HSO (5655).)The rating of the NPN open-collector output is 30 mA (30 V or lower) maximum, and residual voltage is 0.5 V.The rating of the Non-voltage input is ON voltage 1 V or lower, and OFF current 0.6 mA or lower. *6 Select either the Distance mode or the Profile mode. (Only distance mode is available with the LT-9501HSO (5654) and LT-9001HSO (5655).) The rating of the NPN open-collector output is 30 mA (30 V or lower) maximum, and residual voltage is 0.5 V. The rating of the Non-voltage input is ON voltage 1 V or lower, and OFF current 0.6 mA or lower. |
Датчик измерения Keyence LT-9501H
Controller, Not Subject to Export Control, with Camera Function
Описание
Получить КП
Для получения коммерческого предложения, пожалуйста, вышлите ваш запрос на электронную почту info@keyence-sensors.ru с указанием требуемых позиций и реквизитами компании.
Похожие товары
Закрыть
Датчик измерения Keyence GT-H10
Sensor Head
Закрыть
Датчик измерения Keyence OP-26751
End unit (2 pcs.)
Закрыть
Датчик измерения Keyence GT-75AP
Amplifier Unit, Panel Mount Type, PNP
Закрыть
Датчик измерения Keyence OP-77678
Contact, Standard Type
Закрыть
Датчик измерения Keyence GT-H10L
Sensor Head, Low Measuring Force Type
Закрыть
Датчик измерения Keyence OP-77682
Contact, Superhard Type
Закрыть
Датчик измерения Keyence GT-71A
Amplifier Unit, DIN Rail Type, NPN
Закрыть
Датчик измерения Keyence GT-H22L
Sensor Head, Low Measuring Force Type