| Model | LK-G3000P*1 | |
| Type | Separate monitor model*2 | |
| Head compatibility | All LK-G sensor heads are compatible | |
| Connectable number of heads | Maximum of 2 units | |
| Display | Minimum display unit | 0.01 µm |
| Display range | ±9,999.99 mm to ±9,999.99 µm (Selectable from six levels) | |
| Display cycle | 10 times/sec | |
| Terminal block | Analogue voltage output | ±10 V x 2 outputs, output impedance: 100 ? |
| Analogue current output | 4 to 20 mA x 2 outputs, maximum load resistance: 350 ? | |
| Timing input | For OUT1, voltage input | |
| Reset input | ||
| Auto-zero input | ||
| Laser remote interlock input | Non-voltage input | |
| Comparator output | For OUT1, PNP open-collector output | |
| Alarm output | For OUT1, PNP open-collector output (N.C.) | |
| Expansion connector | Timing input | For OUT2, voltage input |
| Reset input | ||
| Auto-zero input | ||
| Program switching input | Voltage input x 3 inputs | |
| Laser-Off input | For Head A/Head B, voltage input | |
| Comparator output | For OUT2, PNP open-collector output | |
| Alarm output | For OUT2, PNP open-collector output (N.C.) | |
| Binary | Binary output | Measured data output (21 bits), OUT1/OUT2 selectable, PNP open-collector output |
| Strobe output | PNP open-collector output | |
| Binary selector output | ||
| Binary selector input | Voltage input | |
| RS-232C interface | Measured data output and control input/output (Maximum baud rate: 115,200 bps, selectable) | |
| USB interface | In conformity with USB Revision 2.0 Full speed (USB1.1 compatible) | |
| Major functions | 2 OUT simultaneous measurement, Operation, Averaging, Filter, Calibration, Measurement, AUTO ZERO, Sampling frequency setting, Mutual interference prevention, Data storage, 8-program memory, ECO mode, ABLE setting, Target setting, ABLE tuning, Selection of measurement surface of transparent target, Statistics processing, Connection of setting support software, Selectable head-mounting, etc. | |
| Rating | Power voltage | 24 VDC ±10 %, Ripple (P-P) 10 % or less |
| Current consumption | 500 mA or less with 1 head/600 mA or less with 2 heads | |
| Environmental resistance | Ambient temperature | 0 to +50 °C |
| Relative humidity | 35 to 85 % RH (No condensation) | |
| Weight | Approx. 370 g (including the cable) | |
| *1 The rating of the PNP open collector: 50 mA max. (30 V max.), residual voltage of 1 V max. The rating of voltage input: 10.2 V or more ON voltage (26.4 V max.) 0.6 mA or less OFF current. *2 LK-G3000P can be operated singly. The measured value display and setting modifications can be performed on the display panel (LK-GD500) or via the setting support software (LK-H1W). |
Датчик измерения Keyence LK-G3000P
Separate controller, PNP output
Описание
Получить КП
Для получения коммерческого предложения, пожалуйста, вышлите ваш запрос на электронную почту info@keyence-sensors.ru с указанием требуемых позиций и реквизитами компании.
Похожие товары
Закрыть
Датчик измерения Keyence OP-25218
Expansion connector for DIN rail amplifier
Закрыть
Датчик измерения Keyence GT-A22L
Sensor Head, Low Measuring Force Type, Air Cylinder Model
Закрыть
Датчик измерения Keyence GT-71AP
Amplifier Unit, DIN Rail Type, PNP
Закрыть
Датчик измерения Keyence GT-A22
Sensor Head
Закрыть
Датчик измерения Keyence OP-77679
Contact, Flat-plate Type
Закрыть
Датчик измерения Keyence GT-75AP
Amplifier Unit, Panel Mount Type, PNP
Закрыть
Датчик измерения Keyence GT-H22L
Sensor Head, Low Measuring Force Type
Закрыть
Датчик измерения Keyence OP-76874
Head Mounting Bracket A