Model	LJ-G5001
Head compatibility	Compatible
Number of connectable sensors	2 units max.
Display	Minimum display unit	0.1 µm*1, 0.001 mm2, 0.01 °
Maximum display range	±99999.9 mm, ±999999 mm2, ±99999.9°
Input terminal block	Laser remote interlock input	Non-voltage input
Trigger input	For sensor head A, non-voltage input
Timing 1 input	Non-voltage input
Auto-zero 1 input
Reset input
Output terminal block	Analogue voltage output	±10 V x 2 outputs, output impedance: 100 ?
Total judgment output	NPN open-collector output
Error output	NPN open-collector output (N.C.)
Process output	NPN open-collector output
Trigger input enable output	For sensor head A, NPN open-collector output
Adjusted error output
Expansion connector	Timing 2 input	Non-voltage input
Auto-zero 2 input
Trigger input	For sensor head B, non-voltage input
Program switching input	Non-voltage input, 4 inputs
Memory card save input	Non-voltage input
Laser-Off input	For sensor head A/B, non-voltage input
Judgment/Binary output	3-level judgment output: OUT1 to OUT8, total judgment output Binary output: OUT1 to OUT8 measured data output (21 bits) NPN open-collector output*2
Strobe output	NPN open-collector output
Trigger input enable output	For sensor head B, NPN open-collector output
Adjusted error output
Analogue RGB monitor output	SVGA (800 x 600 pixels)
RS-232C interface	Measured data output and control input/output (Maximum baud rate: 115200 bps, selectable)
USB interface	In conformity with USB Revision 2.0 HI-SPEED (USB 1.1 Full-SPEED compatible)
Ethernet interface	100BASE-TX/10BASE-T
Memory card	Compatible with NR-M32 (32 MB), GR-M256 (256MB), and NR-M1G (1GB). (with FAT32)
Major functions	Sensor heads calculation, Profile adjustment, Filter, Smoothing, Averaging, Position adjustment, OUT name change, Measurement mode selection (Height, position, gap, width, centre position, section area, intersection, angle, profile comparison, profile tracking), Scaling, Average, Measurement, Measured value alarm, Tolerance setting, Auto-zero, Storage (data/profile), Memory card saving, Program memory, Trigger mode change, Mutual interference prevention, Measuring range change, Calibration, Laser light adjustment, Sampling time setting, Mask, Profile alarm setting, Inclination adjustment, Height adjustment, Display language switch, Setting support software connection, Trigger pitch/Measuring time display, etc.
Rating	Power voltage	24 VDC ±10 %, Ripple (P-P) 10 % or less
Current consumption	800 mA or less with 1 sensor head/1 A or less with two sensor heads
Environmental resistance	Ambient temperature	0 to +50 °C
Relative humidity	35 to 85 % RH (No condensation)
Weight	Approx. 1,050 g
1 When LJ-G015 or LJ-G015K is connected only. When other sensor heads are connected, the minimum display unit is 1 µm. 2 Time-sharing output of judgment results or binary measured data. The rating of the NPN open-collector output: 50 mA max. (30 V max.), residual voltage of 1 V max. The rating of the PNP open-collector output: 50 mA max. (30 V max.), residual voltage of 1 V max. The rating of the non-voltage input: 1 V or less ON voltage, 0.6 mA or less OFF current (Trigger input terminal: 1 V or less ON voltage, 1.0 mA or less OFF current) The rating of the voltage input: 26.4 V maximum rating, 10.8 V or less ON voltage, 0.6 mA or less OFF current (Trigger input terminal: 26.4 V maximum rating, 10.8 V or less ON voltage, 1.0 mA or less OFF current)

Previous product

Датчик измерения Keyence LJ-G015K

Next product

Датчик измерения Keyence LJ-G5001P

Датчик измерения Keyence LJ-G5001

Controller

Описание
Получить КП

Описание

Model	LJ-G5001
Head compatibility	Compatible
Number of connectable sensors	2 units max.
Display	Minimum display unit	0.1 µm*1, 0.001 mm2, 0.01 °
Maximum display range	±99999.9 mm, ±999999 mm2, ±99999.9°
Input terminal block	Laser remote interlock input	Non-voltage input
Trigger input	For sensor head A, non-voltage input
Timing 1 input	Non-voltage input
Auto-zero 1 input
Reset input
Output terminal block	Analogue voltage output	±10 V x 2 outputs, output impedance: 100 ?
Total judgment output	NPN open-collector output
Error output	NPN open-collector output (N.C.)
Process output	NPN open-collector output
Trigger input enable output	For sensor head A, NPN open-collector output
Adjusted error output
Expansion connector	Timing 2 input	Non-voltage input
Auto-zero 2 input
Trigger input	For sensor head B, non-voltage input
Program switching input	Non-voltage input, 4 inputs
Memory card save input	Non-voltage input
Laser-Off input	For sensor head A/B, non-voltage input
Judgment/Binary output	3-level judgment output: OUT1 to OUT8, total judgment output Binary output: OUT1 to OUT8 measured data output (21 bits) NPN open-collector output*2
Strobe output	NPN open-collector output
Trigger input enable output	For sensor head B, NPN open-collector output
Adjusted error output
Analogue RGB monitor output	SVGA (800 x 600 pixels)
RS-232C interface	Measured data output and control input/output (Maximum baud rate: 115200 bps, selectable)
USB interface	In conformity with USB Revision 2.0 HI-SPEED (USB 1.1 Full-SPEED compatible)
Ethernet interface	100BASE-TX/10BASE-T
Memory card	Compatible with NR-M32 (32 MB), GR-M256 (256MB), and NR-M1G (1GB). (with FAT32)
Major functions	Sensor heads calculation, Profile adjustment, Filter, Smoothing, Averaging, Position adjustment, OUT name change, Measurement mode selection (Height, position, gap, width, centre position, section area, intersection, angle, profile comparison, profile tracking), Scaling, Average, Measurement, Measured value alarm, Tolerance setting, Auto-zero, Storage (data/profile), Memory card saving, Program memory, Trigger mode change, Mutual interference prevention, Measuring range change, Calibration, Laser light adjustment, Sampling time setting, Mask, Profile alarm setting, Inclination adjustment, Height adjustment, Display language switch, Setting support software connection, Trigger pitch/Measuring time display, etc.
Rating	Power voltage	24 VDC ±10 %, Ripple (P-P) 10 % or less
Current consumption	800 mA or less with 1 sensor head/1 A or less with two sensor heads
Environmental resistance	Ambient temperature	0 to +50 °C
Relative humidity	35 to 85 % RH (No condensation)
Weight	Approx. 1,050 g
1 When LJ-G015 or LJ-G015K is connected only. When other sensor heads are connected, the minimum display unit is 1 µm. 2 Time-sharing output of judgment results or binary measured data. The rating of the NPN open-collector output: 50 mA max. (30 V max.), residual voltage of 1 V max. The rating of the PNP open-collector output: 50 mA max. (30 V max.), residual voltage of 1 V max. The rating of the non-voltage input: 1 V or less ON voltage, 0.6 mA or less OFF current (Trigger input terminal: 1 V or less ON voltage, 1.0 mA or less OFF current) The rating of the voltage input: 26.4 V maximum rating, 10.8 V or less ON voltage, 0.6 mA or less OFF current (Trigger input terminal: 26.4 V maximum rating, 10.8 V or less ON voltage, 1.0 mA or less OFF current)

Получить КП

Для получения коммерческого предложения, пожалуйста, вышлите ваш запрос на электронную почту info@keyence-sensors.ru с указанием требуемых позиций и реквизитами компании.

Категория: Датчики измерения

Датчик измерения Keyence LJ-G5001

Датчик измерения Keyence GT-A10

Датчик измерения Keyence OP-77678

Датчик измерения Keyence OP-77680

Датчик измерения Keyence GT-72AP

Датчик измерения Keyence GT-H22

Датчик измерения Keyence OP-76877

Датчик измерения Keyence GT-H10

Датчик измерения Keyence OP-77679

Датчик измерения Keyence LJ-G5001

Похожие товары